How to Fix ‘Network Cable Unplugged Error’ issue in Windows

Do you know how to Fix ‘Network Cable Unplugged Error’ issue in Windows? At this point in time, the Internet is definitely one of the most significant components of our digital life. Suppose you were to use your computer without access to the internet. It has been reported that a significant number of users of Windows 10 and Windows 11 are experiencing Network Cable Unplugged issues.

This indicates that their computer is unable to identify the Ethernet connection in an appropriate manner, which brings about errors. Either the desktop or the notification screen is often where the error message is shown. Another way to observe it is by looking at the current status of the Ethernet network connection. Not only is the problem not particular to the Ethernet connection. Even if you are connected to the internet over a Wi-Fi connection, it is still possible for no internet connection to be established.

Following the appearance of this mistake on your computer, it is known to appear at regular intervals, such as every few hours or days. In the event that you are also experiencing this issue, there is no cause for concern. With the use of our methods, we will assist you in fixing this problem. Until the problem is fixed, you need only carry out each of the procedures that are listed below in sequential order. Here are the ways how to Fix ‘Network Cable Unplugged Error’ issue in Windows.

Causes of the ‘Network Cable Unplugged Error’ issue in Windows

1. Loose Cable Connections: A common reason is a network cable that is physically disconnected or not connected properly. The cable should be firmly plugged into both the network port on the computer and the router or switch.
2. Broken wires: Connectivity issues can be caused by broken or faulty network wires. Check to see if the wire is worn, bent, or broken, and if it is, replace it.
3. Connectors That Don’t Work: If the connectors on both ends of the wire don’t work, the connection will be bad. If you find any broken pins or connectors, you will need to repair them.
4. Network Adapter Problems: The problem could be caused by a network adapter driver that isn’t working right or is out of date. You can use the Device Manager to update the driver for the network device or get the most recent driver from the manufacturer’s website.
5. Bug in the Network Port: The computer’s network port might be broken. Use a different port or the cord on a different device to make sure it works.
6. Not Using the Right Network Settings: Connectivity issues can happen when you don’t use the right network settings, like having IP address conflicts or the wrong subnet masks. Check the network settings and make sure they are correct.
7. Turned Off Network Adapter: You can turn off the network adapter in the settings for your OS system. In the Device Manager, make sure that the device is turned on.

How to Fix ‘Network Cable Unplugged Error’ issue in Windows

Verify Network Adapter Settings

1. Press ‘Windows + X‘ and select ‘Device Manager.‘
2. Locate and expand the ‘Network adapters’ section.
3. Right-click on your network adapter and select ‘Properties.’
4. In the ‘Advanced‘ tab, ensure that the ‘Link Speed & Duplex’ is set to ‘Auto Negotiation.’
5. Click ‘OK‘ to save changes.

Disable and Re-enable Network Adapter

1. Right-click on the network icon in the system tray.
2. Select ‘Open Network & Internet settings.‘
3. Click on ‘Change adapter options.’
4. Right-click on your active network connection and choose ‘Disable.’
5. After a few seconds, right-click again and select ‘Enable.’

Update Network Adapter Drivers

1. Return to ‘Device Manager.’
2. Right-click on your network adapter and select ‘Update driver.’
3. Choose ‘Search automatically for updated driver software.’
4. If updates are found, follow the on-screen instructions to install them.

Check Power Management Settings

1. In ‘Device Manager,’ go to the ‘Power Management‘ tab of your network adapter.
2. Uncheck the option that allows the computer to turn off the device to save power.
3. Click ‘OK‘ to apply changes.

Reset TCP/IP

1. Open Command Prompt as an administrator.
2. Type the following commands one by one, pressing Enter after each:
   • netsh winsock reset
   • netsh int ip reset
   • ipconfig /release
   • ipconfig /renew

Conclusion

There are a number of troubleshooters available in Windows that may be utilised to identify and resolve a variety of difficulties, including but not limited to Internet connection, playing sound, blue screen, Bluetooth, and so on. When you use the Internet Connections Troubleshooter to diagnose some Internet difficulties, however, you could occasionally receive the following error message: “Problems found: A network cable is not properly plugged in or may be broken.” Please don’t be concerned; this problem can be resolved. As we move further, we will demonstrate a few different approaches that can be utilised to resolve the issue with the Internet.

Questions and Answers