Table of Contents
It’s possible that you’re having trouble with “PS4 Controller Not Connecting” issue. There are a lot of reports that people who use PS4 controllers are having the same problem, which is very frustrating. At first, it was thought that the problem with not syncing was caused by a connection problem, but that may not be true for everyone. So, if you’re in the same situation, use this guide.
If your PS4 controller stops syncing or connecting all of a sudden, try some of the solutions listed below. Before you go to the troubleshooting guide, we should tell you that you’ll need to check out the Bluetooth connectivity problem properly. Any kind of interference with Bluetooth signals can cause a number of problems.
Game consoles and computers still get the most attention from serious gamers, but Android devices can also be used to play games. Developers have figured out how to use touchscreen controls for their games, but there are also a lot of games that work with Bluetooth game controllers. We mentioned below are the ways to fix ‘PS4 Controller Not Connecting’ Issues.
How To Fix ‘PS4 Controller Not Connecting’ Issues on windows
Reset the PS4 Controller
If your PS4 controller still won’t connect, you could try resetting it to see if that fixes the problem. How to turn off and on a PS4 controller:
- Turn off your PS4 properly.
- Cut off the internet by unplugging the Ethernet cable or wireless router.
- Turn over the controller to the rear and look for the reset button, which is a tiny hole located next to the screw beside the L2 button.
- Insert a thin pin, paperclip, or something you can poke into the slot carefully.
- Push the reset button inside the hole for a few seconds (about five seconds) and then release it.
- Connect the DS4 controller to PS4 via the USB cable.
- Turn on the PS4 and press the PS4 button on the center of the controller to resync until you hear a beep sound.
Re-enable Bluetooth
If your PS4 controller is connected to your Windows PC via Bluetooth but isn’t being seen, you can try to fix the problem by turning on Bluetooth again: Disable the computer’s Bluetooth (from the Windows Action Center or the Windows Settings menu), wait a few seconds, then turn it back on, and then try to pair it with your device again.
Connect the Controller via USB
If your PS4 controller won’t connect to your PC, try connecting it to your computer with a USB cable.
- Turn on your PS4 as usual.
- Insert one end of the USB cable into the back of the PS4; plug the other end into the DS4 controller.
- Wait for some time (about 30 ~ 60 minutes) to get the controller fully charged.
- Press & hold the PS button on the center of the controller to resync.
- You may hear a beep that indicates the controller is pairing with the console.
Use DS4Windows App

What to do if your PC can’t find your PS4 controller over Bluetooth or if your PS4 controller keeps disconnecting from your PC over Bluetooth in Windows 11. The first thing to do is to disconnect the PS4 controller from any devices that use Bluetooth.
- Restart your computer and make sure the DS4 controller has at least 10% battery. (If not, please charge it first.)
- Open Windows search -> type control panel -> select Control Panel.
- Click on the View devices and printers link under Hardware and Sound.
- Look for the Bluetooth PS4 controller -> right click on it & choose Remove device -> click Yes.
After that, you should get & install DS4Windows app and pair the controller.
- Download DS4Windows from the official website; save it to your PC hard drive.
- Double click on the DS4Window installer and follow the instructions to finish installation.
- Go to Settings -> enable Hide DS4 controller -> expand the window by dragging the corner -> click Controller/Driver Setup in blue.
- Minimize the window with a picture of a controller (don’t close it).
- Navigate to Manage Bluetooth Device -> hold share button & PS button for 3 seconds.
- Click to pair the DS4 controller appeared in the list.
Re-enable Bluetooth
- Make sure your controller has enough battery, and then restart your PC.
- Click on your Windows search box and type in Control Panel.
- Choose the first option from the top to open Control Panel.
How To Fix ‘PS4 Controller Not Connecting’ Issues on iPhone
Forget the Controller
If you’ve tried to connect your PS4 controller to your iPhone before and failed, you should remove the controller from your iPhone’s list of Bluetooth devices. Here’s what you need to do.
Step 1: Launch the iPhone Settings menu and select Bluetooth.
Step 2: Next, tap the information icon next to the DualShock Wireless Controller.
Step 3: Select ‘Forget This Device’ and tap ‘Forget Device’ at the prompt.
The PS4 controller will be taken off of the list of Bluetooth devices that your iPhone can connect to. Now try pairing the controller with your iPhone or iPad again and see if a connection is made. If that doesn’t help, try one of the other ideas below.
Reset Controller
Fixing pairing problems is also as easy as putting the DualShock Controller back to its factory settings. To reset your PS4 controller, follow the steps below.
Step 1: Turn the remote and find a small hole in the back near the left shoulder buttons.
Step 2: Use the tip of a paper clip or the SIM card ejector to push the reset button in the small hole for about 3-5 seconds.
Connect in Pairing Mode
Make sure the PS4 DualShock controller is in pairing mode before you try to connect it to your iPhone. This is because your iPhone (and pretty much any other device) can only connect wirelessly to the PS4 DualShock Controller when it is in pairing mode. To put the DualShock controller into pairing mode, press and hold the PS button and the Share button at the same time for about 3 to 5 seconds, or until the light bar on the controller flashes quickly.
- The pairing mode (where the light bar blinks) only takes 60 seconds. So you have one minute to link your iPhone to the PS4 controller.
- After that, the controller will no longer connect to your iPhone because it will no longer be in pairing mode. The point is that you need to move quickly when pairing.
- Go to your iPhone’s Bluetooth settings while the PS4 DualShock controller is in pairing mode, and tap the controller in the list to connect them.
Update iOS
Only iPhones with iOS 16 or later can be used with the PS4 DualShock controller. If your iPhone has iOS 15 or an older version, you should update it. Go to Settings > General > Software Update on your iPhone to see if an iOS update is available.
Charge Controller
Another thing that can stop the DualShock controller from connecting to any device is a low battery level. Make sure the controller is fully charged before putting it into pairing mode. If the remote won’t connect to your iPhone, look at the TV screen to see how much power it has left.
Step 1: With the controller connected to the PS4 console, tap the Share button. This will open the PS4 Share menu.
Step 2: Check the battery icon at the bottom of the menu to see the remote’s battery life.
Step 3: If the controller’s battery is low, plug it into a micro USB power source for a few minutes to charge it, then try pairing it with your iPhone or iPad again.
How To Fix ‘PS4 Controller Not Connecting’ Issues on Android
Reboot Your Device
You can also try to fix the problem by turning off and on your Android device. This problem can sometimes be caused by problems inside the device or by apps that are running in the background that you don’t need. So, restarting your device will help it start over and fix any other temporary problems. You need to take a few quick steps to do this:
- Long press the Power button on your device until the power menu appears.
- Then, select the Restart option from the menu.
- And now wait for your device to reboot. Once rebooted, connect your controller again and check for the problem is gone or not.
Make Use of Official & Best Controller
The next thing you can try is to use the official and best controller that works with COD. To get around these problems on your Android device, you should always use the official and best controller that works with Call of Duty. But the Xbox Core, the 8Bitdo Pro 2, the DualShock PS4 controller Sony DualSense, the SteelSeries Stratus Duo, etc. are some of the best controllers for Android.
Check The Connection
The main reason why the controller isn’t working is that it can’t connect to the internet. So the first thing you need to do is make sure your controller is linked or connected to your device correctly. If you are using a hardwired connection, check the wire. If a wire is broken, it might get disconnected often, which would stop your controller from working.
And if your controller has Bluetooth, make sure it is connected to the right device or that the controller is in Bluetooth range.
Reconnect Your Controller
If you’re using the official controller and you’re still having this problem, try reconnecting the controller to see if that helps. By doing this, a new connection will be made, which will fix the problem that the cod mobile controller isn’t working.
If you’re using a wired connection, unplug your Android device’s wire. Blow on the pin to get the dust off of it, and then reconnect it to your Android device. Or, if you’re using Bluetooth to connect, you can turn off Bluetooth on both the controller and the device and then turn it back on to reconnect.
Verify In-game Settings for Controller Support
You can also check the game’s settings to see if your controller will work with it. Follow the steps below to do this:
- Connect the controller with your device via Bluetooth.
- Next, go to CODM and select Controller setting under the settings menu.
- Now, verify here whether the controller is indicated as connected or not and also the controller support must be enabled.
If you’ve tried all of these solutions and you’re still having the same problem in your Devices, you should go to their official PlayStation support website for more information.
FAQ
How do I fix my PS4 controller not connecting to my PS4?
- If your PS4 controller won’t connect, try a different USB cable in case the first one broke.
- The PS4 controller can also be reset by pressing the button on the back of the controller.
- If your controller still won’t work with your PS4, you may need to contact Sony for help.
Why is my PS4 controller flashing and not connecting?
If your PS4 controller’s white light is flashing, it’s usually trying to connect to the console. This can happen if the controller isn’t connected to the console or if you’re using a new controller that hasn’t been paired with the console.
How do I force my PS4 controller to connect?
- Hold down the button for the PlayStation for 3 seconds.
- Press and hold the PlayStation button and the “Share” button, which is above the arrow buttons.
- Now, the light bar should flash. In the Bluetooth window on your PlayStation, choose the controller you want to use.
Why is my controller blinking and not connecting?
If your Xbox One controller is flashing. If you press the Xbox button on your controller and it blinks or flashes, this usually means that your controller isn’t paired to a console. As was already said, this can happen if you pair the controller with another system but aren’t near it.
Why is my PS4 controller light blue and not working?
If you see the “blue light of death,” it could mean that your power or HDMI cables are broken or not working properly. Here’s how to tell if that’s the issue. Press and hold the Power button until the PS4 beeps twice and turns off. Disconnect all your PS4 cables.