Table of Contents
This guide is about Fix ‘Macrium Reflect Clone Failed’ Issue. So read this free guide, Fix ‘Macrium Reflect Clone Failed’ Issue step by step. If you have query related to same article you may contact us.
Fix ‘Macrium Reflect Clone Failed’ Issue – Guide
Macrium Reflect is a cloning and imaging tool that lets you move data or systems from one hard drive to another without reinstalling Windows. However, there is a small chance that the Macrium Reflect clone has failed with an error message. In addition to error 9 in the above case, you may also get read error 13 broken pipe, error creating disk overview, 0x8000ffff, permission denied, read error 22, write error 22, invalid argument, disk not found, failure on file system check, error 8, error 0 etc.
You may encounter Macrium Reflect Clone Failed error message when cloning your hard drive to an SSD or a new hard drive. If that happens, what should you do? The first step is to discover the reasons that caused the Macrium Reflect clone to fail. Once you know the reasons, you can follow the solutions in this article to efficiently fix the error.
How to Fix ‘Macrium reflection clone failed’
Users who experience this issue report that they receive a variety of error messages such as ‘access denied’ or ‘unable to match partition’. This error message is usually accompanied by error digits such as ‘error 9’, ‘error 0’ etc. In rare cases, if the permissions are not set correctly, you may get the message ‘read failed 13 permission denied 32’ or ‘write failed 22 invalid argument’ along with the original error string.
The solutions listed below address all of these issues. Make sure you have an active Internet connection and are logged in as an administrator.
Check the disk for bad sectors
A bad sector is a sector on a storage device that is inaccessible to any software due to permanent damage. Bad sectors are present in the storage device all the time. To counteract this, the operating system flags these sectors so that it can ignore them in normal operations. If you have any bad sectors, run the ‘chkdsk’ utility to ensure it doesn’t interrupt the cloning process.
To clean up Destination Disk
If the destination drive has a corrupted file system, Macrium will not be able to clone to it. Corrupted file systems are also not uncommon and are often induced because of logical errors. We can use the ‘diskpart’ utility to clean up the target drive structure and see if that fixes the problem.
Try disabling the antivirus
As mentioned earlier, antivirus software blocks access to any programs they deem suspicious of infecting your computer system. If the cloning process is blocked by an antivirus, you may get the error “Access Denied” along with an error code.
To avoid this situation, you can disable your antivirus software completely and try to clone again. If you have more than one antivirus software on your desktop, do the same for all of them. Once you are absolutely sure that no antivirus is monitoring your computer, try running the cloning process again.
Create an image instead of cloning
If you’re having trouble cloning our hard drive, you can try taking an image of it. There are slight differences between the two processes. Disk cloning is the procedure of copying the entire contents of one drive to another, which includes all the information necessary to allow you to boot the operating system from the drive. It creates an individual copy of the hard drive and these hard drives can also be replaced with each other after the cloning process.
Disk imaging is the process of making a backup copy of the contents of a hard drive. A disk image is a type of storage file that contains all the data and information needed to boot into the operating system. However, the disk image needs to be applied for the hard drive to work. Here, we will outline the procedure. how to imagine your drive instead of cloning.
Ignore bad sectors
If you get the same error message when creating an image, you can try to ignore the bad sectors when the image is being created. Typically, following solution 1, all bad sectors are removed from logical storage. But if there is any problem that is still causing problems, that might solve the problem.
Check unit connection
Before starting to use third-party alternatives, you should verify that the physical connection between the two units is adequate. If you are connecting an SSD via a USB port, try plugging it into the motherboard and try cloning again.
Change the hard drive’s SATA connection and, if possible, try changing the cable. Cables can be easily damaged and, because of them, the cloning process can be interrupted. Once you are sure that the target and target drives are properly connected, proceed with the cloning process.
Try out third-party alternatives
If all of the above methods don’t work for you, you may want to consider using alternative software. According to our research, there were several cases where Macrium generated an error condition, while other software like AOMEI did the job perfectly. For user information, we recommend AOMEI software. You can download the software module from its official website and try to clone your drive from it.
Final note
I hope you like the guide Fix ‘Macrium Reflect Clone Failed’ Issue. In case if you have any query regards this article you may ask us. Also, please share your love by sharing this article with your friends.