The Best Gateway for Tech Trends

Copyright 2023 @compsmag - All Right Reserved
Blogs

Guide: Factory Reset a Belkin Router

by Justin Barry
by Justin Barry

This guide is about Guide: Factory Reset a Belkin Router. So read this free guide, Guide: Factory Reset a Belkin Router. If you have query related to same article you may contact us.

Guide: Factory Reset a Belkin Router – Guide

Belkin branded routers can perform a cold reset if there are problems with their current settings or if access to the router is accidentally disabled. The hardware reset function can be performed on Belkin routers by following the steps below. Resetting a Belkin router will remove all current settings and return to factory default settings. Do not perform a reset unless you have the necessary information to configure the router with the correct settings that will be required after the reset is complete.

How to Belkin Router with Factory Reset

  • If your router does not enter reset mode by pressing the reset button button, check the power supply. Sometimes the power supply may be bad and you will not be able to enter the mode. In that case, the other option is to reset the Belkin router to its original configuration. To do this, connect a jumper from the power supply to the reset port. This will allow your router to enter reset mode.
  • The next step is to verify that the wireless card is working properly. You can do this by looking for WAP. It should be identified as Wireless Access Card in Device Manager. If it’s not working properly, try replacing it with a new one. Remember to disconnect the power supply before trying to reset the router.
  • If everything was fine, you can now start resetting your Belkin router using the steps mentioned earlier. When you want to reset your Belkin router from factory, it is necessary to turn it off. Then remove the battery from it. After that, plug the power cord into a USB port on your computer and insert it into the back of the router.
  • Now, you need to open the router box. When opening it, you need to be very careful. You have to make sure you don’t damage anything by doing this process. You need to remove all circuits to see if they are working properly. If you find that there is something wrong with the circuits, try replacing them. Belkin router usually has reset/switch port for different connections and models.
  • When finished, remove all components from the Belkin router. Put them back in the box where you received them. You can connect the power supply back to the computer now. When finished, check that the Belkin router works as well as before.
  • In some cases the Belkin router will not restart even though you have followed all the steps mentioned above. The reason behind this issue is that the reset port on the modem does not work correctly. This is a common issue that occurs with some Belkin router models. To reset your modem, you need to plug the power cord into the reset port and press the reset button button. If you find that the reset button is not pressed, the cable is probably defective.
  • It is important to find out the technical details of your Belkin router before resetting it. Find out if you need to make any modifications to make it work correctly. If you need to reset the router, try resetting it manually first. When you are dealing with the reboot button, be sure to keep all wires out of your hands as they can be easily damaged.
  • If everything is working fine, you can try resetting your Belkin router using the factory reset port. First unplug the power cord, then plug in the reset port on the back of the Belkin router. You can find instructions on the manufacturer’s website at how to restart your router. After resetting the router, follow the instructions carefully to return the device to reset status.

    • Final note

    I hope you like the guide Guide: Factory Reset a Belkin Router. In case if you have any query regards this article you may ask us. Also, please share your love by sharing this article with your friends.

    You Might Be Interested In
    Blogs DailyguiderobertGuides and Tutorialsguiding17How To GuideHow To GuidesTipsTricks
    Justin Barry

    Justin Barry has been writing about technology as a career for more than a decade at this point. The majority of that time was spent as a freelance writer covering a wide variety of topics, some examples of which include mobile phones, wearables, tablets, smart home devices, laptops, augmented reality, virtual reality, mobile payments, and fintech.

    Leave a Comment

    * By using this form you agree with the storage and handling of your data by this website.

    You may also like

    How to Fix “Discord Error Code 1006” issue on Windows 11/10

    How to Fix “Helldivers 2 Quickplay Not Working” issue

    How to Fix “Helldivers 2 login limit reached” issue

    How to Fix “TikTok Picture Swipe Not Working” issue

    How to Fix “Network Adapter Error Code 31” issue on Windows 11/10

    How to Fix “Location Is Not Available” issue in Windows 11/10

    Where technology meets possibility" "Compsmag has Proudly Shared Free Information Since 2014.

    This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More